specifications subject to change without notice. all dimensions in inches. ? copyright 1998 the connor-winfield corporation 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com 3.3v surface mount 7.5x5mm crystal clock oscillator hsm9 xo the connor-winfield hsm943, hsm933, hsm923, and hsm913 are 7.5mm x 5mm, 3.3v lvcmos, surface mount, fixed frequency crystal oscillators (xo) designed for use in all applications requiring precision clocks. the rohs compliant surface mount package is designed for high-density mounting and is optimum for mass production operating specifications parameter minimum nominal maximum units notes frequency range (fo) 1.544 - mhz hsm943 125 & 155.52 hsm913 170 hsm923 170 hsm933 170 frequency tolerance - ppm 1 hsm943 -20 20 hsm913 -25 25 hsm923 -50 50 hsm933 -100 100 operating temp range -10 - 70 c supply voltage (vdd) 2.97 3.3 3.63 vdc supply current (icc) - - ma 1.544 to 31.999 mhz 15 32 to 49.999 mhz 20 50 to 66.999 mhz 25 67 to 124.999 mhz 40 125 to 170 mhz 50 absolute maximum ratings parameter minimum nominal maximum units notes storage temperature -55 - 125 c supply voltage (vcc) -0.5 - 7.0 vdc features: 1.544 to 170 mhz 3.3v operation rohs compliant tri-state enable/disable power saving function: 10ua when disabled overall frequency tolerance: hsm943 20 ppm, hsm913 25 ppm hsm923 50 ppm, hsm933 100 ppm temperature range: -10 to 70c ceramic surface mount package tape and reel packaging notes: 1. inclusive of calibration @ 25c , frequency vs temperature stability, supply voltage change, load change, shock and vibration , 15 years aging. 2. oscillator output is enabled with no connection on pad 1 bulletin sm007 page 1 of 2 revision 28 date 18 may 2006 us headquarters: 630-851-4722 european headquarters: +353-61-472221 input characteristics parameter minimum nominal maximum units notes enable voltage - (vih) 70% vdd - - vdc 2 disable voltage - (vil) - - 30% vdd vdc enable time - - 10 ms disable time - - 150 ns output disable current (lcc) - - 10 ua lvcmos output characteristics parameter minimum nominal maximum units notes load - - 15 pf voltage high (voh) 2.91 - - vdc low (vol) - - 0.33 current high (loh) -2 - - ma low (lol) - - 2 duty cycle at 50% of vcc 45 50 55 % rise / fall time: 10% to 90% - - 6 ns 0.8v to 2.4v - 1 1.5 20% to 80% - 1 2 start-up time - - 10 ms jitter (10 hz to 20 mhz) - - 5 ps rms (12 khz to 20 mhz) - - 1 ps rms
specifications subject to change without notice. all dimensions in inches. ? copyright 1998 the connor-winfield corporation 2111 comprehensive drive aurora, illinois 60505 phone: 630- 851- 4722 fax: 630- 851- 5040 www.conwin.com bulletin sm007 page 2 of 2 rrevision 28 date 18 may 2006 pin connections 1: tri-state e/d 2: ground 3: output 4: vdd dimensional tolerance: .02? (. .005? (. 1 dimensional tolerance: .02? (.508mm) .005? (.127mm) soldering general conditions 260c max x 10 sec max x 2 times max or 230c max x 180 sec max x 1 time typical operation data (vapor phase reflow) 20 to 100 sec up to 215c, 50 sec at 215c, then down to room temperature per 1 to 5c / sec environmental characteristics temperature cycle the specimen shall meet electrical characteristics after tested 5 cycles of -55c / 30 minutes and +125c / 30 minutes hermetical no bubbles appear in flourinert (fc-43) at 125c 5c for 5 minutes solvent resistance marking will withstand immersion in isopropyl alcohol or trichloroethylene suggested pad layout ordering information hsm943 - 125.00 mhz clock series center frequency mechanical characteristics free drop the specimen shall meet electrical characteristics after tested 3 times, free drop testing on the hard wooden board from a height of 75 cm. vibration the specimen shall meet electrical characteristics after tested by the following conditions: 10-55hz 1.5mm amplitude, 55-2000 hz 20 g's, 2 hours for each plane thermal shock after applied thermal shock of 260c max x 10 sec max x 2 times, or 230c max x 180 sec max, the specimen shall meet electrical characteristics solderability (eiaj-rcx-0102.101 condition 1a) 1) flux: mil-f-14256 (ww rosin=25%, isopropyl alcohol = 75%) 2) solder: qq-s-571 (sn = 63%, pb = 37%) 3) solder bath temperature: 235c 5c 4) depth of immersion: up to electrical terminal 5) immersing time: within 2 sec 0.5 sec into solder bath after performing the above procedures, a newly soldered coverage shall be greater than 90% after performing the above procedures, a newly soldered coverage shall be greater than 90% after performing the above procedures, a newly soldered coverage shall be greater than 90% after performing the above procedures, a newly soldered coverage shall be greater than 90% after performing the above procedures, a newly soldered coverage shall be greater than 90% test circuit marking information part marking number v ariations hsm913 hsm913xx hm913xx hsm923 hsm923xx hm923xx hsm933 hsm933xx hm933xx hsm943 hsm943xx hm943xx xx = date code output waveform tape and reel dimensions package characteristics package hermetically sealed ceramic package and metal cover
|
